Pellet & Powder Kits Include:
Breech plug grease
Nipple pick
Cotton swab (Pellet pack only)
Bronze bristle brush
Quick loaders (2)
XTP Hunter saboted bullets with re-usable ammo tubes
.50 caliber = 240 grain
.45 caliber = 180 grain
#11 capper
209 primer capper
Loading/cleaning jag
Bullet/ball puller
Cleaning patches
Bullet starter
Bore solvent
Field nipple wrench
Flask (powder pack only)
Powder measure (powder pack only)
Video
 

The Traditions Sportsman's Package supplies you with everything you need to start Muzzleloading today! (Expect for powder and caps/primers.)  You will be able to LOAD, SHOOT & CLEAN your muzzleloader with the items included with this package. The FREE Video will show you "The Basics of Muzzleloading" and also provides you with exciting hunts and tips to impove your shooting.

*Cleaning Bore Brush

10-32 thread size

Instructions for use:

1. Attach the brush to the end of your ramrod.
2. Spray some Bore solvent into bore or on brush and push into bore.
3. Use a back and forth motion to scub inside of bore. This will loosen up the fouling in bore.
4. Use bore swab (included with Pellet Shooter's kit only) or cleaning jab with patches attached to ramrod to clean ou loosened bore fouling.

*Nipple Pick

This accessory is used to clean out the nipple or breech plug powder residue or debris that may be preventing ignition.

Instructions for use:

1. Make sure the firearm is UNLOADED!
2. Slide the pick out by pushing button up towards curved end.
3. Insert pick into nipple or breech plug tole to remove debris.
4. Replace pick into body by pulling back on button.

*Breech Plug Grease

Use this grease to lubricate the breech plug threads or nipple threads before installing muzzleloader. Before shooting for the first time the breech plug and nipples should be cleaned and lubricated. This will prevent stuck breech plugs.

Instructions for use:

1. Rotate cap until the tip covers the O-ring.
2. Push plunger up into body of syringe to start the flow of grease.
3. Apply to threads.
4. When finished, rotate cap away from O-ring.

Note: You can cut the applicator down to get a larger flow of grease.

*#11 Capper

Holds 17 #11 percussion caps.

Instructions for us:

1. Pull the button all the way back and old in position.
2. Hold capper with loading port facing upward.
3. Place #11 cap into loading port, open side down, and repeat until you have loaded the desired amount of caps.
4. Carefully release the follower and allow follower to move forward and rest on last cap.
5. Push cap forward in loading postion with thumb.
6. Using gentle pressure seat cap on nipple.
7. Pull capper out and away from nipple.

*Magnum Quick Loaders

These loaders are used to hold up to 150 grains of powder and a projectile. Holds 3 .50 caliber pellets.  They can be carried safely in a pocket or fanny pack to quick access.

Instructions for use:

1. Load projectile into shallow end of tube with point facing out.
2. Load powder or pellets in deeper end. measure amounts of powder first with calibrated measuring device before loading into tube.  If using pellets have the black igniter end of pellet facing outward.
3. When ready to charge the muzzleloader, open the cap with powder in it and place over top the crown of the barrel.  Line up so not to spill any powder.
4. Next, open the other side of tube and load projectile into bore with point facing out.

Use only Black Powder, Pyrodex or Pelletized powder. Make sure projectile is seated firmly on top of the powder charge.

*Bore Solvent

Use solvent when cleaning your muzzleloader.  Spray on patches or parts to be cleaned. Wipe off with dry cloth. For heavy fouling, let solvent soak in bore for deep cleaning action.

*Projectiles

These projectiles are fully assemble and packaged in a re-usable ammo tube. can be used to hold extra bullets, shot, or other accessories that will into tube.

Instructions for use:

1. Make sure that bullet seated inside the plastic sabot with pointed facing out.
2. Seat bullet with Bullet Starter. Please refer to Manufactor's Instruction Manual for recommended loading data.

Make sure bullet is firmly seated on top of powder charge. Always use eye and ear protection when loading or shooting any firearm.

*Powder Flask

(Included with Powder Shooter's Kit Only) Holds Black Powder or Pyrodex only.

Instructions for use:

1. Unscrew top cap.
2. Pour powder into flask body.
3. Replace top and tighten.
4. Turn flask upside down.
5. Place spout over powder measure.
6. With thumb,  push valve button to allow powder to pour.
7. Fill powdermeasure to recommended charge.
8. Release valve button to stop powder flow.
9. Never pour powder directly from flask into barrel.

*209 Capper

Holds 12 primers in body plus one in loading area.

Instructions for use:

1. Squeeze the wire in the back until it releases from the capper.
2. Fill capper up with primers and reattach spring.
3. Push one primer over the front.
4. Load primer into nipple and pull out and away.

The half circle on laoding end may be used as a deprimer.

*Ball Starter

Helpful item to "start" the bullet into the bore.

Instructions for use:

1. Place bullet on top of bore with tip facing out.
2. Place short arm of starter over top of bullet and push down into bore.
3. Ise longer arm to seat bullet farther down into bore.
4. Use ramrod to fully seat bullet on top of powder charge.

Note: Make certain that bullet is fully seated against the powder charge. Never stand in from of or lean over bore when loading. Use proper eye and ear prtection when shooting or loading.

*Ball Puller

Use to pull out stuck projectile or objects in bore. Can be used to unload muzzleloader when needed. Use on end of ramrod.

*Cleaning/Loading Jag

Use to load projectiles and to clean bore with lubed or dry patches. Use on end of ramrod.

*Nipple Wrench

Removes and installs nipples into your muzzleloader.

Instructions for use:

1. Use small end of wrench for #11 nipples and larger end for 209 nipple.
2. Secure end of wrench over top of the nipple.
3. Install or remove nipple.

*Powder Measure

(Included with Powder Shooter's Kit only) Use only Black Powder or Pyrodex. Be sure to follow manufacturer's recommended loading data. Fill measure to recommeneded charge of powder. Pour powderinto muzzle.

Traditions offers you the largest selection of muzzleloading funs and accessories.

Item #: A5101