Search
Browse by Manufacturer
Browse Categories
PcsOutdoors Right Panel PcsOutdoors | Trapping Specials Page

Wall Mounted Fleshing Beam Mount


Price : $70.00
In Stock
Item Number : WallMount
Manufacturer : Badgerland Trapping Supply
Manufacturer Part No : WallMount

 

This wall mounted fleshing beam mount is the strongest, and sturdiest mount on the market. This mount can be mounted to just about anything with a profile of less than 1". For those trappers with space issues, you can slide fleshing beam in and out for quick cleaning and storage, with only the plate left on the wall. Beam bracket comes pre-drilled to fit any fleshing beam width 5" and up. Each mounting bracket comes with 4 - 5/16" x 2 1/2" carriage bolts with washers to mount to fleshing beam to bracket. This mounting system is the last one you ever buy.

 

INSTALLATION DIRECTIONS:

  1. Lay fleshing beam on a hard, flat, sturdy surface upside down. Take beam bracket and lay the side with the four 3/8” holes face down and centered on fleshing beam.  Beam bracket should be 1” past the end of fleshing beam.  Now mark holes.

  2. Drill marked holes with a 5/16” bit.

  3. Install four 5/16” carriage bolts through fleshing beam and beam bracket and tighten securely.

  4. Before you mount your plate, here is a great place to start. Figure out what height you would like the point of your fleshing beam to be from your standing surface.  These measurements should give you point of reference to start from.  If you mount the top of plate at 23”, this will put a 48” long fleshing beam point at 41” from standing surface.  You can use these measurements to help with adjusting to your liking.

  5. Mount wall plate to desired height with pocket facing upwards. There are 2 options with this. 

    a.) If mounting to studs mark 9/16” holes (using the wall plate as a template) and pre-drill with a ¼” bit. Mount with ½”x 3 ½” lag screws and tighten securely. This will attach the wall plate to one wall stud.

    b.) Manufacturers recommend to anchor a piece of 2” x 12” to two wall studs at needed height. Then, attach wall plate to the 2” x 12” with 4 ½” lag screws or drill 4x 9/16” holes through the 2” x 12, attach nuts/washers, and tighten securely.

  6. Now your fleshing beam with bracket can be slid into wall plate. Your beam can now be slid in and out with ease without compromising strength and sturdiness for a lifetime of use.  Unlike other beam mounts, ours allows 100% use of your fleshing beam.

<< Previous in Fur Handling Equipment Next in Fur Handling Equipment >>

Related Products

AuSable® Brand Hardwood Fleshing Beam
AuSable® Brand Hardwood Fleshing Beam
MSRP: $54.00
Price: From $35.00 to $42.00
ratingratingratingratingrating
AuSable® Brand Hardwood Fleshing Beam
Hardwood Fleshing Beam. Grade "A" Quality. These heavy duty beams are tapered to a point. Great for using with two handles fleshing knives. Works for coon, badger, beaver.
Fiberglass Fleshing Beam
Fiberglass Fleshing Beam
Price: $34.95
ratingratingratingratingrating
Fiberglass Fleshing Beam
A trapper/fur dealer who has used this item for years with no noticeable wear has designed this fleshing beam. It will last the trapper a lifetime of normal use.
Fiberglass Fleshing Beam and Pre-trimmed Insert Combo
Fiberglass Fleshing Beam and Pre-trimmed Insert Combo
Price: $47.95
ratingratingratingratingrating
Fiberglass Fleshing Beam and Pre-trimmed Insert Combo
Here is our combination of the fiberglass fleshing beam along with its specially designed wooden insert. This combination has been used by expert fur handlers who deal with thousands of furs each year.
Floor Mounted Fleshing Beam Mount
Floor Mounted Fleshing Beam Mount
Price: $75.00
Floor Mounted Fleshing Beam Mount
This floor mounted fleshing beam mount is the strongest, sturdiest mount on the market. It also has the lowest profile with less than 1" for those trappers with space issues. The fleshing beam bracket comes pre-drilled to fit any beam width 5" and up.
J & J Wall / Bench Mount Fleshing Beam System
MSRP: $125.00
Price: $105.00
You Save: $20.00 (16 %)
ratingratingratingratingrating
J & J Wall / Bench Mount Fleshing Beam System
The J & J Fleshing System is truly a "one of a kind" system. This fleshing system mounts to a wall or to the end of your work bench. Easily stores out of your way when not in use or for cleaning up when you are done fleshing and stretching your furs. The
Pre-Trimmed 2
Pre-Trimmed 2"x8" Insert for Fiberglass Fleshing Beam
Price: $17.00
ratingratingratingratingrating
Pre-Trimmed 2"x8" Insert for Fiberglass Fleshing Beam
Pre-Trimmed and formed 2"x8" wooden insert for use with the fiberglass fleshing beam. Insert length is 48". Fiberglass beam and insert have a total length of 60".

Product Reviews

Rate This Product:
or Create a Review
(0 Ratings, 0 Reviews)
Shopping Cart
Your cart is empty.
Untitled Document
Join Our Email List
PcsOutdoors Right Panel

Printable Mail Order Forms